Search results

I did speak to a lady today and she said yes. But they would say anything to get you to transfer over. Just wanted a confirmation before I transfer.

Evening Forum I spoke to a lady at NICEIC in December and she said that the NICEIC might be combining Part P and PIR in January. Does anyone know if this has gone ahead? Thanks

where do i alter the dip switches and links?

Evening forum, I was asked to change an old programmer for a modern one which was easy enough. They have since noticed that there is no room stat and have asked me to add a wireless stat. It is a Y plan. DO i just wire the receiver into the wiring center as i would with a wired one? Is there...

If you are using a test meter with a NO TRIP function for your Zs then you will always get a higher measured value than calculated. With you saying it was on a ring where you got the high reading then there is no doubt it is on an RCD. Then this high reading is expected.

I applied for this. It is a credit account that you have 60 days interest free. You can use this card at screwfix and B&Q. I have been granted this with a nice credit limit.

Do i then take it that, from the spur it gets wired into the stat? So if i was to run a 2.5 T&E from the spur to to stat would that be ok? Thanks

[quote name='Andy

Evening Forum I have been asked to fit underfloor heating. I have never done this. Does anyone know where i could get some help from on how to do this. Especially the wiring side for the thermostat and spur. This is to go in a bathroom. Many thanks

At the back of BS7671 where it shows a ring circuit, it says something like - space heaters should preferably not be run of the ring that is protected by 30/32amp fuse/mcb. Running it of a radial should be ok but then you looking at possible overloading. I would try and run a separate circuit.

Evening Forum My suppliers only had MR16 fire rated down lighters although i wanted GU10. They have given me the MR16 down lighters and GU10 lamp holders/ leads and told me to just change them over. The lamps for the MR16 are 36 degrees Celsius and the GU10 are 40 degrees Celsius? Can i do...

The 4mm cable is soldered to the earth sheath and to the met. From the met to the consumer unit it is 16mm.

Hi Forum. First of all thanks to everyone who gave advise on 2391 exam, the wait is over and i passed. I m being assessed at the end of August and i have left my project a bit late. I was going to upgrade the fuse board in my house until today i realised it was a TN-S supply and the earth is...

i would try another B6 first just in case it is the mcb. I would not go any bigger than 6. That is more than big enough for what is on the circuit. Type C breaker has a bit more tolerance to sensitivity. However if you change the type of mcb from a B to a C You would then have to test the earth...

Thanks for the overwhelming response. The reason why i wanted to use 4mm ring is 2.5 reference method C can only carry 27amps and the loads might not be distributed evenly on the ring.4mm can carry 37 so with it being protected by 32amp breaker i know i am safe. Thanks

Evening Forum Quick question. New kitchen is being fitted and i have been asked to do the wiring. There are quite a few integrated appliances such as washing machine, dishwasher, microwave and tumble dryer. There are also 6 under wall unit lights and then 6 double socket outlets. I have decided...

My new landlord gives me loads of work, thats how i got the house. Sometimes a make no money cause the job is so small.

:^O :Applaud:

Yes thats right and even though BS7671 is non-statutory as long as work is best carried out to regs, that is what will prove my innocence.

We just had our assessment with NICEIC with the company i work for as approved contractor. I asked about exporting earth and the answer was there are no regs stopping anyone exporting earth on a TN system. If TT the outside building has to have its own stake/rod. I AM NOT LOOKING FOR AN ARGUMENT...