Don't you just hate it when.........?

[welshwizard]

Quite right, Nicky.

 

[kme]

Chip board floors are easy, Just cut out a BIG square with a circular saw. It needs to be big cos a narrow piece will lose its strength, Then add some 2 x 1 to the joist edges and that simple. A big square gap is easier to fish through than a narrow floorboard size gap.

I make a hole 25mm, and send my white mouse down, with a bit of string tied round him. Then I wait for him to move a little in the direction I want him to go. I`ll put my phone over the hole, and play a cat`s purr.

The little fella legs it with my bit of string, and Bish! Bash! Bosh! Job done.

How Cool is that. ?:|B)

 

[a1]

PMSL @ KME.

 

[SPECIAL LOCATION]

I make a hole 25mm, and send my white mouse down, with a bit of string tied round him. Then I wait for him to move a little in the direction I want him to go. I`ll put my phone over the hole, and play a cat`s purr. The little fella legs it with my bit of string, and Bish! Bash! Bosh! Job done.

How Cool is that. ?:|B)

Thats the same method I was taught at college!

and the lecturer said it was his OWN special trick!!!

DOH!!!

I bet everyone's been doin it for years???X(X( X( ]

Bet your going to tell me your mouse is called 'Gary' as well?

oh and of of course 'Andrew' if its 3-phase???

 

[kme]

Thats the same method I was taught at college!and the lecturer said it was his OWN special trick!!!

DOH!!!

I bet everyone's been doin it for years???X(X( X( ]

Bet your going to tell me your mouse is called 'Gary' as well?

oh and of of course 'Andrew' if its 3-phase???

Don`t talk soft.

You can`t use a mouse and 25mm for 3 phase - holes`re too small. Doh

That`s when the German Shepherd comes into her own.B)

p.s. cctv - talking cameras. That`s all I`m saying.

 

[SPECIAL LOCATION]

Don`t talk soft. You can`t use a mouse and 25mm for 3 phase - holes`re too small. Doh

That`s when the German Shepherd comes into her own.B)

p.s. cctv - talking cameras. That`s all I`m saying.

That must of been when I fell asleep at the back of the class! :|

I wondered what that Blo**y dog was doing in me tool box!!!!!?????

 

[SPECIAL LOCATION]

DYJHIW

you go to get a specific tool out of your toolbox...

and its not there!!!!

not in the place where you always keep it!? :_|

and you start racking your brains......

where did I use it at last....

I'm sure I remember putting it away at the end of the last job...

you go through all of your other toolboxes... where you never keep it..

and its not there either...

and you go round again check again...

re check the back of the motor..

the footwells...

under the seats...

in the glove box!! X(

back round the toolboxes again.... :_|

still not found!! X(

two or three days go by....

and you find it.....

EXACTLY WHERE YOU LEFT IT!!

In the wrong Bl***y place!

In the really bad situations...

you find it just after you have bought a replacement!

+++++++++++++++++++++++++++++++++++++++++++++++++

Me trusty Stanley Knife when AWOL on Sunday!

I convinced myself I had left it on a job from last Wednesday!

But then I found it......

outside resting on my kitchen window sill..

from when I had to trim the end off the garden hose.

cuz it had come out of the tap fitting adaptor! :|

EXACTLY WHERE I HAD LEFT IT.... git!!! X(