Agreed Lurch. A heavy enough psu would be around the £60 Mark... Just seems a shame to have them sitting there.
I keep saying I'll have a clear out and get all my old (sh*t) used tools on flea bay - I'm sure I'd make a few quid as people will by ANYTHING!
Cheers.
The cheap batteries aren't much cop - I've had a few... I don't want to buy more machines spending more money.
The whole idea is to make use of what I've got. I'll let you know if I find anything...
Hi,
I've got a drill graveyard in my store including 2 off 24V makita's (brh24?).
I'm looking for a mains in; 24VDC out PSU to hard-wire into the machine (or even chop into a old battery) to bring them to life as corded tools. They are quality machines and good for labourers to use for...
Thanks for the replies chaps...
Got a plan sorted - it's a really old building with a pig of a route back to CU. Going to swap CU (no RCD's) then run a 40A 10mm radial to a little board in cooking area feeding 3 16A radials with 3 pin sockets.
Turning into quite a nice job actually...
Hi,
Got bit of a question...
Looked at a job (large takeaway shop)... They have a single 32A ring to cooking area - appliances (kebab, Bain Marie etc) are on plug tops...the twin surface skts are soon burning out - this must be due to the length of time the appliances are in use and the load...
Hi,
Has anyone heard of a 'globus homes VX1 voltage optimiser'?
As voltage optimisers go, they seem very good value or cheap & nasty.
Mate of mine rates them - it's not my area as yet... Any comments?
Would value your input!
Darren.
Zero earth - 1000 ohms Zs.
I should've pulled the fuse really. The old dears have DNO fitting PME & cut out next week.
CU is wooden wylex.
It's been bothering me! What would you do...?
The black cover allows access to the N terminal and the moulded case of the incomer does have an earth symbol on it together with cable entry points... There's no official PME stickers though.
Looked at a job yesterday. The suppliers kit looked recently upgraded.
There is a facility on the suppliers incomer to connect an earth - but, there is no labling to say it is permissible to use as a PME.
I've tried to upload a pic but it's too large.. I've cropped it and it workedaq
Btw...
Great having a spare to 'make fit'...
You know... I've got a thing about burnt neutral terminals (as per my last but few post).
I'm convinced there are more burnt neutrals than lives... but no-one knows why.
Maybe I need to get out more (or a holiday?...lol!), but I'm getting a bit OCD about...
Thanks KME!
The cams in the kit have RJ45 connections but no dip switches to set an address . This is why I think they aren't IP.
Actually, the UI on the stock client is quite slick.
The kit retails on Amazon around £200 - not cheap?
Cheers.
Hi,
Had the joy of installing a customer supplied kit the other day. It's a samsung 'mickey mouse' kit with 2 cams and a DVR.
The cams are connected with CAT5 cable and terminated at each end with RJ45's.
Customer wants me to supply and install another 2 cams. It doesn't look like the cams...
Yes, armourings used as cpc - Zs at sub board is good. This shows good mechanical contact at both ends of the SWA to chassis.
With this in mind, I'll make a C3 observation due to no banjo's - I'm sure you can understand my original question when I'm quizzed about the comment?
Btw, I tend to...
Hi,
Did an EICR recently - one of the 3P subs used a 35mm 4C SWA.
There was no banjo at either end - Zs was fine (testing with only cable CPC/armourings)
Can't find an actual reg saying a banjo is needed...opinions on the classification?
Cheers.